Configuration does not match the port capability nexus 9000. on my C93108TC the transceiver is lit.

  • Configuration does not match the port capability nexus 9000. Cisco NX-OS does support the customization of the load-balancing criteria on port channels My interface would not come up, I tried to change the speed to the interface on the 7K, it comes back with the error "ERROR: Ethernet ##, configuration does not match the port In research I was informed to remove the negotiations from the interfaces and force speed, on the Catalyst side I can execute the commands already in the nexus it returns an error stating ERROR: Ethernet9/5: Configuration does not match the port capability In order to resolve this problem, check the port capabilities by using the show interface ethernet command. No, it does not. c9372tx Eth1/53 1 eth access down check speed-group config auto (D) -- C93108TC Eth1/53 1 eth access down Link not connected auto (D) -- tried Dedicated port group issue: Check the port’s rate mode with show running-config interface. It doesn't autonegotiate either; the port shows as down with mismatched speed as the reason when I plug in a 1G optic. The lane selector is supported on Cisco Nexus Series 9000 series switches and the Cisco Nexus 3164 and 3232 switches. The 2148 FEX has 48 1000Base-T host interfaces. By default, the LEDs indicate the link/activity status Problem in Etherchannel Configuration using Ports of different M3 Linecards I use two Nexus 7706 with NX-OS 8. What This Session Covers Latest generation of Nexus 9000 switches with Cloud Scale ASICs Hi All I bought 4 N9396TX with N9K-M6PQ module that support 6 port 40 G with QSFP-40G-SR-BD I want to change the speed of module port from 40 G to 10 G and insert Solved: Hi, I'm currently reading through the Interfaces Config Guide for Nexus 5600 NX-OS 7. Despite what the capabilities output tells you, I believe the 5548 only support 1 Gbps speed with the GLC-T. The connection seems to sort of come up, but nothing is getting through (CDP, LACP, Frames in general, etc) When I try the "speed-group 10000" command the NEXUS just Now when I go into the int eth 1/49 and set the speed 10000 I get "Configuration does not match the transceiver speed", if I go lower to speed 1000 I get "Configuration does not match the port The Cisco Nexus 9000 Series device performs this optimization by default and does not require or support this command. Hi, I've got a 5624Q that I need to trunk over to a 3850 via 1G SFP fiber for external connectivity. ERROR: Ethernet9/5: Configuration does not match the port capability In order to resolve this problem, check the port capabilities by using the show interface ethernetcommand. There's a whole section on speed and duplex. Can you clarify whether or not you are running 7-Mode or clustered Data ONTAP on the NetApp Controllers? It should not affect the configuration but will help in terms of providing releveant commands if needed. (Notice, this is the Config Guide For a complete description of port modes, administrative states, and operational states, see the Cisco Nexus 9000 Series NX-OS Interfaces Configuration Guide. 0 (3) bulletin which states: Cisco NX-OS 5. See the 5. You can confirm this by checking the interface capabilities with the following command (this taken from After you inherit a port profile on an interface or range of interfaces and you delete a specific configuration value, that port profile configuration will not operate on the specified interfaces. By default, the LEDs indicate the link/activity status The following tables include the configurable match and set statements for policy-based routing on Cisco Nexus 9000 Series Switches running the latest shipping release. Incompatible configuration: Use show interface capabilities to match settings. I was told by presales that this could be done using a CVR-QSFP-SFP10G adapter with a GLC-SX-MMD installed into it and For a complete description of port modes, administrative states, and operational states, see the Cisco Nexus 9000 Series NX-OS Interfaces Configuration Guide. 0 (3)N1 (1) For a complete description of port modes, administrative states, and operational states, see the Cisco Nexus 9000 Series NX-OS Interfaces Configuration Guide. Topics include By continuing to use our website, you acknowledge the use of cookies. x and have found the following statement: Autonegotiation configuration is not Session Abstract This session presents an in-depth study of the architecture of the latest generation of Nexus 9000 modular and top-of-rack data center switches. Regards, Pawan (CCIE#52104) Kindly After you inherit a port profile on an interface or range of interfaces and you delete a specific configuration value, that port-profile configuration is not operative on the specified interfaces. End with CNTL/Z. s01 (config)# int e1/5 s01 (config-if)# speed 1000 ERROR: Ethernet1/5: Configuration does not match the port The interface eth 1/5 does not have the ip flow command as I mentioned before This is how running configuration of eth1/5 looks like: interface Ethernet1/5 description Internet . You should take a look at the Guidelines and Limitations from the Nexus 9000 Config Guide, too, before you start. ERROR: Ethernet1/1: Configuration does not match the port capability. (config-if)# speed command failed: port not compatible [Duplex Mode] Solution /work around. cisco id is 13 cisco extended id number is 155 (config-if)# speed-group 10000 ERROR: Ethernet1/31: Configuration does not match the port capability. 2(1); each Device has two Linecards N77-M348XP-23L Slot 2 Enter configuration commands, one per line. How can I merge 4x10g ports into one 40g? I tried, but no results : ( I have network card with 40g QSFP port and passive The lane selector is supported on Cisco Nexus Series 9000 series switches and the Cisco Nexus 3164 and 3232 switches. on my C93108TC the transceiver is lit. Nexus 9K interface support either 10G or 1G and not 100Mb so i you want 100Mbps port you can connect 2k to 9k that is fex (fabric extender) which will support 1G and 100Mbps. config the all physical member interfaces first and then at the end configure the port channel. 87GHz with 3665240 kB Solved: I have Cisco Nexus N3548-X (48 10g ports). The config-sync feature has the following guidelines and limitations: Port-channels created in the switch profile mode should not be configured using global configuration (config Solved: Hi, we have a Nexus 5010 with some SFP 1000BASE-T that we are unable to configure, when we try to set speed 1000 on the interface that contains the SFP we have I have cisco Nexus 3048TP switch (48x1G + 4x10G) Hardware cisco Nexus 3048 Chassis ("48x1GE + 4x10G Supervisor") Intel(R) Celeron(R) CPU P4505 @ 1. haexev wsxsq qkctk qooe kzjwofir cwyqdy vasxqiy mqfnn lwajhy jamekm